Saturday, October 5, 2013

Error Ink Pads Epson L200

Epson L200 is an All-In-One printer, All-In-One printer is a printer unit has multiple function as Scanning, Photocopying, and printing.

Epson L200 comes with 6 ink bottle consist of 3 Black Ink, and colored ink, 1 bottle for Cyan, 1 bottle for Magenta, and 1 bottle for Yellow Colors. This set of inks can yield approximately 18,000 pages for black and 6,500 pages of colored print.

Epson L200 adopt the technology of using an ink tank or before a converted printer done by the third party.

Epson L200 comes with many advantage and on the other hand, also we expect some worst problem arising from it. The common problem with this printer are the following; no power, printing problem, ink pumping, and blotted image.

Such a problem can not print then out error " The printer 's ink pads are at the end of their service life ." When we take it to the place of service usually they reasoned that it should be replaced . Actually quite reset printer epson l200 with software Adjustment Program for Epson L200 .His manner is very simple reset


    Run the Adjustment Program for Epson L200 , choose Particular adjustment mode .

  1. Run the Adjustment Program for Epson L200 , choose Particular adjustment mode . 
  2.  
  3.  In the next window select the Maintenance menu Waste ink pad counter then click OK
  4. At Waste ink pad counter window , click the Check button , you will see the value of each point on the counter . In the picture below looks Pad Counter Main section has passed through a maximum value . To reset select each counter , then click the button Initialization
  5. It would appear the message pop - up " When the OK button is clicked , the initialization is done" click OK
  6. Turn the printer off , then turn it on again and wait a few moments .
  7. To check whether the counter value has been successfully reset , press the Check button , Main pad counter value should be changed to 0 % . Click Finish to exit .   

Epson L200 printer has been successfully reset, then do a test print to ensure good printer

https://www.mediafire.com/file/eds9b7daksc1hmt/Reseter_Epson_L200.rar/file
                                                                Link Download File:
http://raboninco.com/Gbj


 

Saturday, August 24, 2013

head cleaning epson R230x

1. Turn on the Epson Stylus Photo R230 printer or yours R230x
2. Click Start> Control Panel> select Printers and Faxes> Epson R230
3. Click Select Printer Printing Task prefference on the box that is on the right side of the window or can 

    also right-click on the Epson R230 and select Printing Prefferences
4. Select the Maintenance tab dialog box appears so that these


5.Then select Head Cleaning as shown in the picture above that I put a red circle, it will 
   display a dialog box like this
Select the start like in the picture above that I marked in red arrows, then this machine will do the print head cleaning, ink pumping Please wait for the printer to finish.

Epson R230x paper jam problem repair



 
R230X, R230,R220 epson printer suddenly could not pulling the paper so the paper can not get in to do the printing and sometimes even encouraged, but paper still can not get even get damaged paper
Epson R230 printer has 2 paper roll that serves interesting, this roll is located at the top and bottom of the printer, the printer In this type often have constraints that can not pull the paper at the time of print, the problem is usually caused by not working epektifnya rubber roll the many things that cause the rubber does not work well.which are:

 
1. Rubber is not abrasive (slippery)
2. A lot of dirt that sticks to the surface of the rubber
3. Rubber surface is bare



To overcome the above problems are many things we can do, from start fixing up the new one to replace it
To fix this follow the following steps:


1. Open the printer lid up to the opening roll.
2. Two roll rubber washer uses ordinary water course until clean.
3. Dry the rubber roll that has been in the washing to dry
4. Add seltipe the rubber where the rubber needs to be fixed purpose meeting and rather thick
5. Plug it back into its original position
6. completed

 
Hopefully the above tips can solve a problem with your printer, if there are any questions please leave a comment on this post.

Thursday, August 22, 2013

Canon GENERIC "S" SERIES RESET CODE

Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER button.
(3) Release the RESUME button, Next press and release the RESUME button two(2) more times in
succession. Note: you are still holding the POWER button). The printer's carriage will "reset"
or move momentarily. If the above was properly performed the printer will enter the
"Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout. javascript:void(0)
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.

resetter epson r230x (SSC Service Utilily)




1. Make sure the printer is turned on and terkonek with a computer (printer driver already installed)
2. Install SSC Service Utility and run the program
3. Model of printer configuration settings. Select the Epson Stylus Photo R230. After the play closed

   windows.
 4. In the lower right corner of the taskbar (near the clock) right click the icon SSC Service Utility, select
     " Protection Counter" click "Reset protection counter" select Yes on the pop up that asks
    "Have you  Replace waste ink pad"

 







5. Restart the printer, the printer is ok

That's the steps I described to my friend, so she does not go back and forth to the printer lift handyman service to reset Epson R230. May be useful.


               Link Download File:
http://adf.ly/7tyCh


Canon Pixma IP2770 Error 006

To resolve Error 006 on Canon iP2770
1. Canon iP2770 Driver uninstall then restart
2. then install again
3. do reset the service tools program
4. print as usual
5. completed

Canon Pixma IP2770 Error 5100

Error 5100 occurred at Canon iP2770 Printer This is usually caused because they are not detected by the Printer Cartridge. So the message Error 5100 We inform that the printer can not find its cartridges. Steps that must be done
1. Turn off the printer
2. Remove both cartridges from the printer
3. Use a cloth moistened with alcohol to clean the surface of the contact / terminal connector that touches

    Cartridge printer / could also use a pencil eraser
4. Replace the two Cartridge
5. Turn on the printer.

Printer Canon IP2770 Error 5200

When iP2770 is turned on, the printer looks normal with LED Flash GREEN. But after ordered to do pengeprinan, the error 5200 would show up, and the LED will turn green ngeblink orange 1x to 8x
For error 5200 Printer Canon IP 2770/2700 is the same as I fix Error 5B00 above but for this error problem you just need the first step Error 5B00 following:


1. Make sure that the printer Canon IP 2770 / IP 2700 is turned off (Off) But the power cable  


    (power) installed.
2. Press the RESUME button for about 2 seconds
3. After that you press the POWER button until the green light on (when pressing the POWER button,

    Resume button not released yet)
4. Then release the RESUME button, but do not release the POWER button.
5. POWER button while still depressed, press the Resume button 5 times. Led will light turns green to

    orange last flame orange. (not to be mistaken 4x because the printer will die in total, but also temporary)
    while reading the writing on the nature of the above.
6. Release both buttons simultaneously.
7. LED will blink briefly then will flash GREEN.
8. The computer will detect the new device, just ignore it
9. Press the Power button so that the printer OFF / Off
10. Once the printer is completely dead then press the Power Button Back then the computer will turn on

    and be ready for use again.

Service tool pixma ip2770 (Resetter Pixma iP2270)


steps reset canon pixma iP22700: 
 - Log on to the service mode first connect the printer to the computer and the power cord without turning
  on the printer (the printer is turned off). 
- Press the Resume button about 2 seconds and then press the POWER button until the green light on 
   (when pressing the POWER button, Resume button jgn removed) 
- Then off the RESUME button, but do not release the button POWER
While the POWER button still depressed, press the Resume button 5 times. Led will light turns green to
   orange last flame orange. (not to be mistaken 4x because the printer will die in total which means that the 
   steps we have to reinstall from scratch)
- Then release both buttons simultaneously, the LED will blink briefly then will flash GREEN.
- At this time the computer will detect a new device, just ignore it and wait until the process is complete.
- This situation shows the iP2770 printer is in a state of SERVICE MODE and ready to reset

for permanent service
  
1. Download Resetter
2. Exctract File Resetter iP2770. 
2. Service Tool ServiceTool_V1050



 

3. Click the "MAIN", then the printer will proceed, then iP2770 will print one page
    with the words "D = 000.0
4. Click "EEPROM Clear".
5. Then click "EEPROM", and the printer will print the results iP2770 Resetter. One line in his writings as 
    follows: "TPage (TTL = 00000)" 
5.  Turn off the printer by pressing the POWER button.
6. Up here if all goes well, it's too printer will reset and is back Normal.

the following ink may have run out calour canon MP250, IP 2270, MP160, iP2700

When the printer is turned on seems OK, but after the print command, it will display Blink 13x Orange on the Canon MP250, MP160, iP2770, iP2700


 the following ink may have run out Color

Blink 13x Orange lights with the picture above, means catrid color reset press the Resume button requires a bit longer until the GREEN light flashes, then release. black catridge also need to be reset and the picture is as follows:

 the following ink may have run out Black



Same way: rather long press the Resume button until the GREEN light flashes, then release.after doing these steps then the printer will return to normal. This often occurs when the cartridge runs out complete refill then installed again.